From specs available to me online, the 2022 Keystone Outback 328RL Travel Trailer is 37.58 ft. (451 in.) in length as measured from back bumper to coupler. The Adco Olefin HD All-Climate + Wind RV Cover for Travel Trailer, # AD39ZR is a great fit for this travel trailer as it is overall 447" long x 106" wide x 102" tall. This will fit over the travel trailer and probably provide options of enclosing the propane tanks as well, pulling tight with included cinch ropes leaving the coupler... view full answer...
Without knowing what you have in your coach I can't say for sure if we have a replacement, David.
What we do have is the Replacement Unismart Remote Control for Furrion Indoor TVs, Stereos, and Fireplaces # FR34FR which is a universal remote that'll work with Furrion fireplaces and the Replacement Remote for Greystone RV Fireplace # LC22TF which will replace the remote for the Greystone F2653BCGW.
If your coach doesn't have either of these then unfortunately we don't have a replacement,... view full answer...
The Adco AquaShed part # 290-52244 that you referenced is for RV lengths between 26'1" - 28-1/2' long so yes this is the same size. view full answer...
Yes, you will definitely need the PWM Filter # VGR64VR to properly power your Furrion Vision S RV Camera System # FOS43TASF. In 2020 GM switched to PWM wiring so your 2023 will send a constant 12 volts to the camera, which typically leads to a lot of connectivity issues.
There is the Furrion adapter # FR87PR as well, but with GM's towing technology it's going to keep sending you an error on the in-dash monitor saying you aren't connected to the trailer or that you need check your running... view full answer...
Furrion Vision S RV Camera Systems like the # FOS43TASF have a 492' range so the length of your trailer isn't to blame here. Most likely the unit is getting enough power to turn on and sometimes pair and then loses the signal as the voltage drops. The solution to this is to pull the camera back off of the trailer and splice in the PWM Wiring Adapter # VGR64VR behind it so that it gets a steady 12 volts in order to properly operate.
I've attached a video below where I'll walk you through... view full answer...
It is certainly possible to upgrade or downgrade for that matter the spring bars on a weight distribution system. That said, this is not an option for all weight distribution systems with the main factor being age and parts available.I am not sure which exact model you have as Reese/Draw-Tite make several and the correct springs bars will be based on said model. I can say that most of the newer systems are branded as Reese so there is a good chance the spring bars for the older Draw-Tite... view full answer...
The Dexter Electric Trailer Brake Kit part # K23-462-463-00 is designed for 4,400 lb axles with a four bolt mounting flange. If this is what you have then it will work great. The axle capacity can be found on the axle tag sticker in the center of the beam. Unfortunately, we cannot look up parts for any one specific trailer. The kits is for two assemblies. view full answer...
From what I've been able to determine, your axle is a AL/KO 4400 lb axle, which would use a 10 x 2-1/4 inch brake assembly.
Dexter offers a set of self adjusting brake assemblies, part # K23-478-479 that would be compatible, but I'd like you to measure the bolt hole spacing of your brake mounting flanges, just to be sure. If the top holes are 2-7/8 inches apart and the bottom are 3-1/4 inches apart as shown in the provided photo, then the # K23-478-479 would work for you. view full answer...
We have two options for a switch matching your 3/4" x 1/2" dimensions. For white you need the # 37213645 and for black the # 37212815. These have cutout dimensions of 0.745" tall x 0.5" wide and the actual switch dimensions are 0.756" tall x 0.508" wide. view full answer...
Your 2016 Keystone Outback 324 CG uses 12 inch brake assemblies like the part # AKEBRK-6 but we don't have a way to determine what replacement shoes you'd need as it would be based on the brand of brake assemblies you have and we don't have a way to determine that. view full answer...
Assuming the 36 foot measurement you took was for the body of your Keystone Outback travel trailer (not including the tongue), we do have a superb option for winter weather that will fit your trailer:
- Adco Olefin HD All-Climate + Wind RV Cover for Travel Trailer # AD39ZR
The # AD39ZR fits trailers that are between 34'1" and 37' long, and is specifically designed to offer your trailer the best protection against all the elements it can face, including the snow and wind that you'll see... view full answer...
We have a couple of potential options for you, however, we do not have any 9" square jack pads that you're needing.
The closest square jack pad we have is the Replacement Pad for SnapPad Jack Stand Pad System # SN37FR. This jack pad will fit an 8" square jack foot, and measures 11-1/2" in diameter.
Alternatively, we do also offer the Replacement Pad for SnapPad Jack Stand Pad System # SP54FR. Which will fit 9" round jack feet, and measures 11" in diameter. view full answer...
I reached out to my contact at Dexter and based on the serial number you provided your axle was made in October of 2008 and will use braking assemblies # 23-455 for the passenger side, and # 23-454 for the driver side.
I included videos of the products mentioned for you to take a look at. view full answer...
I believe you are asking for a replacement fireplace for the Greystone Wf2613. The exact replacement for the Wf2613 fireplace according to Greystone is Greystone 26" Electric Fireplace with Crystals - Recessed Mount part # 324-000069. view full answer...
To determine if we have leaf springs that will fit your Keystone I would need to know the length of your current springs. Common sizes are 26 inches like the part # e22YR.
Your U-bolts would work fine. view full answer...
Thanks for the photo, that was a huge help!
You're needing 1/2 inch wire loom, which we sell by the foot as part # 459075-1. I'd also use some 1/2 inch loom clamps, part # A0500 to secure the wire loom and hold it where it's supposed to be. view full answer...
As long as your 2015 Keystone Outback 316RL Trailer is equipped with 3" round axles (which would be typical for 5,200 pound units) the Roadmaster Comfort Ride Shock Absorbers # RM-2460 will work perfectly. This kit is designed for tandem axle trailers like yours, is compatible with your existing MorRyde system, and will absolutely help to smooth out the ride of your trailer during travel. This is going to provide a significant improvement in terms of side-to-side movement and bounce on... view full answer...
The Sew-In Snap Tape for RV Curtains part # 37281005 use a standard size snap fitting which is not called out specifically by the manufacturer. The most important thing is to be sure you get the correct connectors based on your track such as the Snap-In RV Curtain Carrier part # 37281075.
I have attached a full list of the connectors below as well. view full answer...
I am happy to help you install the Curt Triflex part # C24VV in your 2019 Ford Expedition with a factory 7-way. I recommend to use Curt Custom Wiring Adapter for Trailer Brake Controllers part # C51436 to install the brake controller. It will plug into a built-in port under the dash of the Ford and the other end plugs into the brake controller to power the brake output circuit on the 7-way to tow a trailer with brakes. view full answer...
The hitch ball for the 16K Equal-i-zer Weight Distribution System w/ 4-Point Sway Control # EQ64FR can actually be found as part # EQ54FR and is rated for 16,000 lbs just like the weight distribution system.
This same hitch ball is likely used for some of the lower-rated systems from Equal-i-zer as well. Basically if the system comes with a 2-5/16" hitch ball and isn't rated for more than 16K it likely has this hitch ball.
Attached are some review videos for you to check out. view full answer...
Go To Results